Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
What are your opinions regarding How to Install a Bathtub?
Setting up a bath tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately hard task. If the old bathtub is conveniently easily accessible, the project can move easily; if you have to open a wall to get rid of the old tub and place the new bathtub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the work and also fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to consider utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub and don't need to alter the setup of your previous water supply pipelines.
Your devices and also product checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather problematic as a result of the restricted access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the faucet in position with the producer provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water supply and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bath tub and also check the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, repair the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the tub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Preparing for the Installation
To start with, the supporting framework provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can fracture fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that article on How to Install a Bathtub from an associate on our other web property. Sharing is good. You won't know, you might be doing someone a favor. I cherish reading our article about How to Install a Bathtub.
Book Services
Report this page